Animation principle of coal washing spiral chute

The animation principle of coal washing spiral chute: 1. Overview of chute sorting, including the process of inclined flow sorting. The slurry is fed to a inclined groove or inclined surface with a certain inclination. With the assistance of flowing water, the ore particles are loose and layered. The upper layer of light mineral materials are quickly discharged to the outside of the groove, while the lower layer of minerals with a larger proportion are stagnant inside the groove or slowly discharged from the lower part. After the difference is connected, the selected ore and tailings can be obtained. Spiral chutes are mining and beneficiation machinery, making them ideal for sand mining and beneficiation in coastal areas, rivers, beaches, and streams. The product also has the characteristics of suitable structure, simple installation, small footprint, easy operation, stable beneficiation, clear beneficiation, strong processing capacity, high efficiency beneficiation concentration ratio, high recovery rate, and stable operation. It has the advantages of small weight, moisture prevention, rust prevention, durability and corrosion resistance, and strong adaptability to fluctuations in feed volume or density, Granularity, and grade. 2、 The mineral mortar with the same technical principle is slowly fed to the surface of the spiral groove through the feeding groove installed at the end of the rotating groove head, and then selected for operation. The bottom of the rotating groove is equipped with a valve block type equipment selection groove, which divides the sorted products into three categories according to grade along the radial direction. By adjusting the position of the valve block to change the acquisition width of each device, the product gathering hopper allows the intercepted variable mineral flow to be converged and exported separately. The transverse plane of the fiberglass spiral chute is particularly suitable for the separation of fine ore materials when the slope of the curve changes. Animation principle of coal washing spiral chute 3. Characteristic FRP spiral chute has attracted more attention among many gravity separation machines due to its low power consumption, simple structure, small area occupation, simple operation, stable beneficiation, clear beneficiation, no moving parts, convenient Computerized maintenance management system, large processing capacity per unit area, etc. The machine has a wide and relatively stable groove surface, and the mortar has a large area of laminar flow, which is more suitable for processing ores with medium and fine (-4mm) Granularity. Glass fiber reinforced plastic chutes with diameters of 400, 600, 900, and 1200MM have been manufactured domestically, Ф The production capacity of 1200mm four heads is about 4-6 tons/hour. The animation principle of the coal washing spiral chute is . The structure of the spiral chute is composed of six parts: a feeding homogenizer, a feeding chute, a rotating groove, a product cutting groove, an equipment gathering hopper, and a groove bracket (including a cross or triangular frame). The spiral groove connected by the rotating plate is a key accessory. The spiral plate is made of fiberglass (fiberglass reinforced coal gangue) and connected together through screws. The sorting surface of the rotating groove has one layer of pre designed durable wear-resistant layer. It has the advantages of lightweight, sturdy, and durable consumer goods. The spiral groove is equipped with a multi tube feeding homogenizer to screen minerals evenly, which is not cumbersome to operate. The mineral sorting equipment is freely stacked on the cross (or tripod) of the support table. The evenly distributed mortar is slowly fed to the spiral groove surface through the feeding groove installed at the head of the rotating groove, and the selection is carried out. The bottom of the rotating groove is installed in a valve block type new equipment to obtain the groove, allowing the sorted new products to be divided into three (or four) new products according to grade along the radial direction. Change the selection width of each new device by adjusting the position of the valve block. The new product gathering bucket is a concentric circular tube that distinguishes and converges the intercepted multi head ore flow. The cross-section of the fiberglass chute and the change in slope of the curve are particularly applicable for the selection of fine-grained materials. 5、 This machine is suitable for separating iron ore, ilmenite ore, Chromite, pyrite, zircon sand, Rutile ore, monazite ore, phosphate ore, tungsten ore sand, tin ore, tantalum niobium ore, niobium ore and other non-ferrous metal ore, rare metal and non-metallic ore bodies with specific gravity difference from fine materials with a particle size of 0.3-0.02mm. Animation Principle of Coal Washing Spiral Chute Animation Principle of Coal Washing Spiral Chute