Belt Chutes and Spiral Chutes

Belt chutes and spiral chutes 1. Overview: The mineral sorting process of the chute belongs to the inclined surface flow sorting step. The slurry is fed to a inclined chute or slope, and under the push of water, the mineral particle group is loose and layered. The upper layer of light minerals is quickly discharged from the groove, while the lower layer of minerals with high specific gravity stays in the groove or flows out at low speed from the bottom. After each is connected, the selected ore or tailings are obtained. Spiral concentrators are equipment for mining and beneficiation, making them ideal for sand mining and beneficiation in coastal, river, sand banks, and creeks. The equipment has a suitable structure, is installed in a simple and simple manner, occupies a small land area, has simple operability, stable beneficiation, clear separation, strong processing capacity, high efficiency beneficiation enrichment ratio, high recovery rate, and reliable operation. There are also advantages such as lightweight, moisture-proof, rust prevention, corrosion resistance, and strong adaptability to fluctuations in feed volume, concentration, particle size, and grade. 2、 Set up the spiral concentrator by using the method, calibrate the vertical line, fix the iron frame or wood at a suitable position, send the sand ore to the two ore inlets on the spiral top by the sand pump, add water, and adjust the concentration of the mineral slurry. The mineral slurry naturally swirls from high to low, generating a coherent centrifugal force in the flow rate of the whirling inclined surface, and obtaining the difference in the density, specific gravity, Granularity and shape of the mineral sand, Through the influence of the gravity of the swirling flow and the centrifugal force, the ore and sand are separated. The selected ore flows into the concentrate hopper and is piped out, while the tailings flow into the tailings hopper and are moved to the sand pit through a pipeline. Then, they are discharged by a sand pump, completing the entire beneficiation process. Belt Chute and Spiral Chute III. Advantages and Characteristics 1. High efficiency, high recovery rate, and accurate ore sorting; 2. No power required; 3. Lightweight, rust resistant, durable, wear-resistant, and corrosion-resistant; 4. Low operating costs and long service life; 5. Strong adaptability to fluctuation of feed volume, density, Granularity and grade; The friction caused by the appearance of 6 diamond sand makes the beneficiation efficiency better than other plastic surfaces. Belt chute and spiral chute 4. The structure of the spiral concentrator consists of six parts: feeding homogenizer, feeding chute, spiral groove, equipment intercepting groove, product gathering hopper, and groove support (including cross or triangular frame). The rotating groove connected by spiral blades is a key component. The rotating plate is made of fiberglass (fiberglass reinforced coal gangue) and connected together by bolts. The spiral groove has a pre made wear-resistant layer on the selected surface. She has the advantages of light weight, strength, durability, and the use of consumables. Above the rotating groove is a multi tube ore feeding homogenizer, which distributes ore evenly and has simple control. The mineral separator is not limited to being placed on a cross (or tripod) on a support table. The uniform slurry is slowly fed to the surface of the rotating groove through the feeding groove installed on the spiral groove head, and sorting is carried out. The tail of the spiral groove is installed in the valve type new product acquisition groove, and the selected new products are divided into three types (or four categories) of new equipment along the radial direction according to grade. Change the selection width of each new product by adjusting the orientation of the valve block. The new product gathering bucket is a concentric circular tube that allows the diverse mineral flows obtained to converge and export differently. The cross section of the spiral chute and the different slopes of the curve are particularly suitable for the separation of fine particle materials. 5、 Scope of use: FRP spiral chute is suitable for separating fine grain iron, ferrotitanium, ferrochrome, pyrite, cassiterite, tantalum niobium, gold, coal, monazite, Rutile, zircon ore, rare earth ore or other metal and non nonferrous metal minerals with sufficient specific gravity difference. Belt Chutes and Spiral Chutes Belt Chutes and Spiral Chutes