Assembly method of spiral chute

The assembly method of the spiral chute is described as follows: 1. The beneficiation chute includes a slope flow sorting process. The slurry is fed to a inclined chute or inclined plane, and under the push of water, the mineral particle group becomes loose and layered. The upper layer of light mineral material is quickly discharged from the groove, while the lower layer of heavy mineral stays in the groove or flows out at low speed from the bottom. After obtaining the concentrate and tailings, respectively. Glass fiber reinforced plastic chutes are mining and beneficiation equipment, especially ideal for mineral mining and beneficiation on beaches, riverbanks, sandbanks, and river beds. The equipment has the characteristics of appropriate structure, simple installation, small footprint, simple operation, stable beneficiation, clear separation of ore, strong processing ability, high efficiency, high enrichment ratio, high recovery probability, and stable operation. And it has advantages such as light weight, moisture prevention, rust prevention, strong corrosion resistance, and strong applicability to fluctuations in ore feed volume, concentration, particle size, and grade. 2、 The production principle is that the evenly proportioned mortar is slowly fed onto the rotating groove surface through a feeding chute installed on the spiral groove head for sorting. The tail end of the spiral groove is equipped with a valve type product acquisition groove, and the selected equipment is divided into three types according to grade along the radial direction. By adjusting the orientation of the valve block to change the cutting width of each product, the equipment gathering hopper allows the selected variable mineral flows to converge and export differently. The transverse plane and slope of the curve of the fiberglass spiral chute vary greatly, and the applicable range is for the selection of fine particle materials. The assembly method of the spiral chute 3. Features and advantages: 1. Large scale and high processing output. Nowadays, the overall requirement for mineral material processing is to use scale efficiency to create benefits. 2. Fine granulation is used for the treatment of fine-grained mineral materials, especially for minerals with a particle size of -0.047mm. The original machinery can generally ensure the recovery of a particle size of+0.047mm. 3. With the development of Hydraulics, two-phase flow, mechanical vibration, etc., GRP chutes have developed from the simple use of gravity and water blocking force to the level of composite application of centrifugal force, equipment vibration force, magnetic force, etc. Through a composite force field, the enrichment of useful mineral materials and the separation of fine and micro particles are increased, thereby improving the mineral recovery rate. 4. The basic starting point is to save energy consumption, reduce energy consumption and protect the environment, occupy small area and space, and consume less water and electricity. 5. Simple and flexible operation, stable sorting process, simple structure, convenient for Computerized maintenance management system. The assembly method of the spiral chute is . 4. The structural composition of the fiberglass chute is composed of six parts: a feeding homogenizer, a feeding groove, a rotating groove, a product cutting groove, an equipment gathering hopper or a groove bracket (including a cross or triangular frame), and so on. The spiral groove connected by the spiral plate is the main component. The rotating plate is made of fiberglass (fiber reinforced coal gangue), which is connected together through screws. The selected surface of the rotating groove has a predetermined wear-resistant layer. It also has the advantages of lightweight, sturdy, and durable consumer goods. Above the spiral groove, there is a multi tube feeding homogenizer for ore dressing and averaging, with simple control. The mineral screening device is freely placed on a cross (or tripod) on a support table. The evenly distributed mortar is slowly fed to the rotating groove surface by installing it on the feeding groove at the end of the spiral groove head, and sorting is carried out. The tail end of the spiral groove is installed in a valve block type new product acquisition groove, and the selected new products are divided into three categories (or four categories) of new equipment along the radial direction according to grade. Change the selection width of each new product by adjusting the orientation of the valve block. The new product gathering bucket is a concentric circular tube that allows the intercepted variable mineral flows to be gathered and exported separately. The cross section and slope of the curve of the spiral concentrator are particularly suitable for the separation of fine ore materials. 5、 This equipment is suitable for separating iron, ferrotitanium, ferrochrome, ferrosulfide, zircon, Rutile, monazite, phosphate rock, tungsten ore, tin ore, tantalum ore, niobium, and other non-ferrous metals, rare mineral metals and non colored metal minerals obtained by gravity difference from fine materials with Granularity of 0.3-0.02mm. Assembly method of spiral chute Assembly method of spiral chute